No products
Prices are tax included
Sensors
-
Electric
- Ozone
- Circulation Pumps
- Pumps, Motors & Parts
- PCB's Packs and Panels
- Lighting
- Sensors and Switches
- Electrical Sundries
- Speakers and Audio
- Heating
- LX
- Air
- Gear
-
Water
- Divertor Valves
- On/Off Valves
- Slice and Ball Valves
- Thermowells
- Unions
- Manifolds
- Floor Drains
- Suction
- Pipe
- Fittings
- Water Filtration
- Check Valves
- Water Features
- Drain valves
- Water Chlorination
- Pipe Clamps
- Gaskets and O Rings
-
Jets and Bodies
- Diffusers & Jets Pieces
- Water Jets
- Waterway Jet Bodies
- SCS Jet Bodies
- Waterway Jet Tools
- Hand-Held Jets
- Wellis
- CMP Products
- FILTERS
- Cycle Valves
- HotSpring-Caldera
New products
-
Hydroquip Low Flow System with K450 touchpad
The Hydroquip Low Flow System is built on Gecko YE5 circuitry utilising...
-
Sundance 850 2002 - 2004
Sundance 850 3 PUMP NT WITH CIRC/PERMAC (Picture for illustration only...
-
Aqua Flo Maelstrom 3hp two speed
Aqua Flo Maelstrom 3hp two speed 2" suction and discharge, exactly the...
-
-
4" CMP Directional Jet - Stainless and Graphite
4" CMP Directional jet, Stainless steel with a Graphite colour jet piece.
-
Hot-Springs Pillow
The Hot Spring Limelight Collection Pillow / Headrest fits the following...
-
Water Tank 2,000 litres
Collapsible water tank. Essential for hot tub servicing. 2metre...
-
-
Light lens and seal kit
Hotspring large light lens and seal kit. Front face diameter 135mm....
-
Hotspring Heater O ring gasket 2"
Hotspring heater o ring gaskets, sold in pairs. Hotspring part number...
-
-
-
-
-
-
-
Waterlab Chamber
Seamless under-the-spa inline integration No intrusive devices in your...
-
Gecko IN.TOUCH 3+ KIT
IN.TOUCH 3+ Kit includes: 2 communication transmitters: In.touch 3+...
-
Gecko IN.TOUCH-3 KIT
IN.TOUCH 3 Kit includes: 2 communication transmitters: In.touch 3 Spa...
This section represents the most common sensors and parts requested.
Every part can be identifiable with a simple comparison of a photograph and the details of the dates at which they have been used on the manufacture of spas.
If you are unsure, call us on the number at the top of the website.
Sensors + Pressure Switches There are 10 products.
-
-
Hi Limit Thermistor (Post 2002) Fine thread
For spas post 2002. Uses the 2 position white board connector with a red and black cable in each pin location. Uses the board connector as pictured. Supplied with O ring
-
-
-
Hotspring Caldera Watkins Pressure Switch Kit
Manufactured by Hydroquip for their triple bend heaters. Also fits the original Hotspring 1.5kw heater. The original switch is square (2nd photo), this is round and fits and works in exactly the same way. Supplied with new cables. The short cable for Hot Spot and the long cable for IQ2020 Hotspring and Caldera heaters. July 2024 - we are the first company...
-
Thermostat Control Thermistor (Post 2002) Coarse thread
For spas post 2002. Uses the 4 position white board connector with a red and black cable in pin locations 1 and 4. Uses the board connector as pictured. Supplied with O ring
-
Thermostat Thermistor (Pre 2002) Coarse thread
For spas pre 2002. Uses the board connector as pictured.
-
