No products
Prices are tax included
Flow Switches
-
Electric
- Ozone
- Circulation Pumps
- Pumps, Motors & Parts
- PCB's Packs and Panels
- Lighting
- Sensors and Switches
- Electrical Sundries
- Speakers and Audio
- Heating
- LX
- Air
- Gear
-
Water
- Divertor Valves
- On/Off Valves
- Slice and Ball Valves
- Thermowells
- Unions
- Manifolds
- Floor Drains
- Suction
- Pipe
- Fittings
- Water Filtration
- Check Valves
- Water Features
- Drain valves
- Water Chlorination
- Pipe Clamps
- Gaskets and O Rings
-
Jets and Bodies
- Diffusers & Jets Pieces
- Water Jets
- Waterway Jet Bodies
- SCS Jet Bodies
- Waterway Jet Tools
- Hand-Held Jets
- Wellis
- CMP Products
- FILTERS
- Cycle Valves
- HotSpring-Caldera
New products
-
Hydroquip Low Flow System with K450 touchpad
The Hydroquip Low Flow System is built on Gecko YE5 circuitry utilising...
-
Sundance 850 2002 - 2004
Sundance 850 3 PUMP NT WITH CIRC/PERMAC (Picture for illustration only...
-
Aqua Flo Maelstrom 3hp two speed
Aqua Flo Maelstrom 3hp two speed 2" suction and discharge, exactly the...
-
-
4" CMP Directional Jet - Stainless and Graphite
4" CMP Directional jet, Stainless steel with a Graphite colour jet piece.
-
Hot-Springs Pillow
The Hot Spring Limelight Collection Pillow / Headrest fits the following...
-
Water Tank 2,000 litres
Collapsible water tank. Essential for hot tub servicing. 2metre...
-
-
Light lens and seal kit
Hotspring large light lens and seal kit. Front face diameter 135mm....
-
Hotspring Heater O ring gasket 2"
Hotspring heater o ring gaskets, sold in pairs. Hotspring part number...
-
-
-
-
-
-
-
Waterlab Chamber
Seamless under-the-spa inline integration No intrusive devices in your...
-
Gecko IN.TOUCH 3+ KIT
IN.TOUCH 3+ Kit includes: 2 communication transmitters: In.touch 3+...
-
Gecko IN.TOUCH-3 KIT
IN.TOUCH 3 Kit includes: 2 communication transmitters: In.touch 3 Spa...
Flow switches are less common in hot tubs than pressure switches. They detect water flow. Water flow moves a tiny paddle that operates a micro switch.
This section also represents the only Harwil flow switches available.
It is EXTRTEMELY important that you follow dimensions and NOT Q-12 codes.
If you Harwil switch is not here, we cannot help - s...
Flow switches are less common in hot tubs than pressure switches. They detect water flow. Water flow moves a tiny paddle that operates a micro switch.
This section also represents the only Harwil flow switches available.
It is EXTRTEMELY important that you follow dimensions and NOT Q-12 codes.
If you Harwil switch is not here, we cannot help - sorry.
Flow Switches There are 9 products.
-
COMMON - Switch only Q-12DS
THIS IS THE MOST COMMON HARWIL. This is the switch ONLY and will fit the three styles of Tee, pictured. With a cable and plug. Thread diameter : 1" - 26mm Grey probe length : 1" - 26mm COMPARE THESE DETAILS WITH WHAT YOU HAVE ! Read down.
-
COMMON Tee 3/4" x 3/4" and switch
Plastic assembly 3/4" x 3/4" barbs at each end and fitted with switch Q-12DS Thread diameter : 1"Grey probe length : 1-1/4" If you don't need the plastic assembly, just buy the switch shown below as an accessory.
-
COMMON Tee 3/4" x 3/4" x 3/8" and switch
Plastic assembly 3/4" x 3/4" x 3/4" fitted with switch Q-12DS Thread diameter : 1"Grey probe length : 1-1/4" If you don't need the plastic assembly, just buy the switch shown below as an accessory.
-
Flow switch 1-7/8 probe (3/4" thread)
60-1008 Long probe version, Length of grey probe arm: 46mm (1-7/8") Outer thread diameter: 20mm (3/4"), Total Length: 90mm.
-
-
Gecko Flow Sensor for XE and YE heaters
Gecko surface mount flow sensor for Gecko XE and YE heaters. SEE PICTURES If you have a flow error with your heater, this is absolutely a first stage repair, to try, before moving onto more expensive parts, ie the spa pack. Supplied : Small plastic block and cable. x2 bolts x1 self adhesive pad (postage stamp size) Scroll down to read more ----
-
Harwil flow switch with transparent Tee...
Flow Switch 1A 3/4" Barb x 1/2" Slip 24" Cord w/2 Pin Connector. Used on Dimension 1 Spas since it has a socket end on the plastic tee to be glued onto the Laing heater. If you don't need the plastic assembly, just buy the switch shown below as an accessory.
