4 core cable for two speed pumps. Colour cable connection information further down.
The 2" end of this Bell Reducer fits on the spiggot end of 2" plumbing and reduces down allowing the use of 1-1/2" fittings.
Used ONLY in Waterway 180° shut off valves. It has a small rubber piece on the stem which makes it different to a diverter rotor. Therefore, DO NOT confuse this part with a divertor rotor.
2-1/2" split nut to fit 2-1/2" suction wet ends and Low Flow heaters. For pumps, this will only ONE pump, the 2-1/2" Waterway. Internal Diameter is 3-1/2"
Clear vinyl 1/8" ID x 1/4" OD. Used for pneumatic switch tubing. Sold per METRE. This NOT for Ozone or other kind of air piping on hot tubs. It is ONLY for pneumatic switches, for baths or VERY old spas. When choosing, for instance, to buy 3metres you will receive one 3m length.
Capacitor for hot tub motors. Specific size for EMG motors by Waterway and Aqua Flo and is supplied with flying leads and ring terminals. Can fit many other pumps, dimensions are shown below. (2021) The motor manufacturer specifically using the 36 (EMG) changed the power to 35 many years ago. We only sell the 35. We cannot buy the 36. You can use the 35...
Pentair diffusers to fit ALL types (regardless of face style) of Medium Pentair jets. Diameter : 50mm Length : 79mm
To fit inside ALL 2" Waterway divertor valves and works with every cap and handle shown in accessories.
Spigot fits inside 2 inch pipe fittings and provides a socket to accept 1 inch pipe
Capacitor for hot tub motors. Specific size for EMG motors by Waterway and Aqua Flo and is supplied with flying leads and ring terminals. Can fit many other pumps, dimensions are shown below.
Laing E14 complete pump with cable and 4 pin AMP connector. Also carries code NSTNDNN2W-05 There is only type of Laing E14 circulation pump so you are guaranteed to have the same water connections when you fit the new pump.
M7 sensor for Metal packs, 24" long. Sold as pairs. You should always replace both sensors at the same time. Best price in the UK and Europe. Complete with o ring and black plastic mount, as pictured.
Pump seal to fit 2" unions - flat type. This gasket is 1/4" thick. Sold in pairs Gaskets are always measured by the internal diameter size of the pipe the fitting is connected to - really confusing when nothing measures what it says. To help, the outside diameter of these is 3" Every hot tub part is measured in inches.
Gate valve seal 2". Valterra Products. Sold individually.
Waterway Two speed 2.5hp pump with the larger 2-1/2" suction
Spigot fits inside 1 inch pipe fittings and provides a socket to accept 1/2 inch pipe
White plug for connecting light cables directly to circuit boards. DO NOT COME WITH PINS which you will need to buy separately.
Waterway 2" Cluster Storm, (twist and click - snap-in jets) Directional Jets These are now the ONLY 2" twist and click Jets available from Waterway. They are Silver Grey in Colour and Directional. NO OTHER style of jets are available in twist and click and 2" They use the 218-5140 diffuser shown below.
56frame - 4hp impellor. For use with Executive Euro 56frame 2hp motors. The MOST common Waterway wet end in Europe. You should also check to see if you need the 2-1/2" suction version of this wet end using our download guide.
Pipe joiner reducer 3/8" RibbedBarb x 1/4" RibbedBarb
Capacitor for hot tub motors. Specific size for EMG motors by Waterway and Aqua Flo and is supplied with flying leads and ring terminals. Can fit many other pumps, dimensions are shown below.
Waterway Plastics - Sealed shut off valve. 1-1/2" socket x socket
IN STOCK Blue Whale Spa Command StormForce 9 are a range of Pumps The StormForce 9 is a main boost pump, WTC200 A pump means it is complete with wet end. 7 amp motor, as original. We were the first company to identify this range of pumps. If your pump is leaking from the back of the wet end you might only need a wet end.
Fitted (loosely) into the rear of Waterway Power Storm jets to channel the water through the jet.
The MOST common impellor used in European Waterway pumps. The same impellor is used in 48 and 56 frame wet ends.
Pentair diffusers to fit ALL types (regardless of face style) of 5" diameter Pentair jets. Diameter : 64mm Length : 100mm
This hot tub heater element is 2kw. Incoloy 800 metal. Standard elements are 10" long and terminal distance of 1-1/4" (A Global Standard) All our elements are 220v for fitting into hot tubs across Europe. They fit ALL 15" long tube heaters made by Balboa, Gecko SSPA, Hydroquip and many others. Will not fit Gecko In.XE and YE heaters - you cannot replace...
These are the highest grade of element in Europe and at the best prices. Will fit all 15" (tube length) heaters and EVERY 2kw Balboa heater. Will not fit Gecko In.XE and YE heaters - you cannot replace elements in these tubes.
Waterway pump known as the Executive Euro. This pump has a standard 2" suction. Two speed code : PF-20-2N22X
Waterway pump known as the Executive Euro. This pump has the larger 2-1/2" suction. Also known as the PF-20***** type. Two speed code : PF-20-2N22X25
Capacitor for hot tub motors. Specific size for EMG motors by Waterway and Aqua Flo and is supplied with flying leads and ring terminals. Can fit many other pumps, dimensions are shown below.
Barb plug for OLD Shur grip manifolds. These DO NOT FIT any of the manifolds in our webshop - they are for the older style Waterway manifolds.
1-1/2" split nuts to fit 1-1/2" suction and 1-1/2" discharge pumps. The best part to use when replacing a cracked pump union. Internal Diameter is 2-3/8"
Waterway 3" Cluster Storm, (twist and click - snap-in jets) Directional Jets These are now the ONLY 3" twist and click Jets available from Waterway. They are Silver Grey in Colour and Directional. NO OTHER style of jets are available in twist and click and 3" They use the 218-6930 diffuser shown below.
3 core cable for blowers, ozonators and single speed pumps. Colour cable connection information further down.
Pack of x4 bolts for 56 frame wet ends, commonly used on EMG motors. They will fit Waterway and Aqua Flo 56 frame wet ends.
Sometimes found screwed into the wet end of hot tub pumps and incorporated into a bleed system. They always seem to snap off when working on wet ends. This part has been discontinued by the manufacturer and there is no alternative made by other companies. Use 672-4350
Waterway 3-3/8" Poly Storm, (twist and click - snap-in jets) Directional Jets These are now the ONLY 3-3/8" twist and click Jets available from Waterway. They are Silver Grey in Colour and Directional. NO OTHER style of jets are available in twist and click and 3-3/8" (Historically, this jet has been available in 4" large Face, now NLA) They use the...
Standard fit lamp holder with 8" cable and terminated with an AMP plug
Fits the 5 Scallop style cap shown in accessories. This part has been discontinued by Waterway, we only have stock on hand and you should contact us before making ANY purchases.
Capacitor for hot tub motors. Specific size for EMG motors by Waterway and Aqua Flo and is supplied with flying leads and ring terminals. Can fit many other pumps, dimensions are shown below.
2" Pump Union x 2" Socket Swept Elbow Tailpiece. Great piece of plumbing. Enables an immediate turn after a pump union without taking up additional space and length.